Media Overview
12. August 2026
News

Parts of a Wind Turbine: Electrical and Power Electronics Explained

Every guide to the parts of a wind turbine walks you up the tower and stops at the generator. This one keeps going, because the anatomy of a wind turbine does not end where the mechanical drivetrain ends. Between the generator and the grid sits an electrical system that decides how much of the captured wind energy actually becomes sellable electricity, and it is the least explained part of the machine. Below you will find every major component, from foundation to switchgear, with an original diagram and extra depth on the electrical side, where ConverterTec has spent 30+ years designing and servicing the frequency converters behind more than 24,500 turbines.

Short answer: A utility-scale wind turbine has five main part groups: the rotor (three blades and the hub), the nacelle housing the drivetrain (main shaft, gearbox, generator), the electrical system (frequency converter, transformer, switchgear and control system), the tower, and the foundation. Longer lists, such as the 12 parts of a wind turbine, simply split these groups into their individual components.

How Does a Wind Turbine Generate Electricity?

Wind flowing over the turbine blades creates lift and drag, the same aerodynamic forces that fly an aircraft. Lift turns the turbine’s rotor at a stately 10 to 20 revolutions per minute. The rotor turns the main shaft, the gearbox steps that rotational speed up to roughly 1,500 rpm on the high-speed shaft, and the generator converts the rotation into electric current. The frequency converter then conditions that raw output to match grid frequency and voltage, a transformer steps it up for the collection network, and the electrical energy flows to the grid. Some designs skip the gearbox entirely: direct-drive turbines couple the rotor straight to a large, slow generator and lean even harder on power electronics.

One scope note before the parts list. This guide describes the horizontal axis, three blade, upwind machine that dominates utility-scale wind farms, onshore and offshore. Vertical axis turbines exist, but mainly in small niches, and downwind rotors are rare. It is this three blade workhorse that has made wind the fastest growing source of renewable energy. If you have seen a modern wind power plant, you have seen the machine described below.

The Main Parts of a Wind Turbine

Here are the main components of a wind turbine in the order the load path meets them, from the ground up. Together they are the answer to what the things on a wind turbine are called.

Foundation

A reinforced concrete base, typically 15 to 20 meters across and buried below grade, that anchors the entire structure and transfers thrust and gravity loads into the ground. Offshore wind uses monopiles, jackets or floating platforms instead.

Tower

Tapered tubular steel sections, bolted at flanges, carrying the nacelle 80 to 120 meters into steadier, faster air. The tower is a part of the turbine in its own right: it houses power cables, ladders or a service lift, and increasingly the converter and switchgear cabinets at its base. Taller towers reach better wind conditions, which is why hub heights keep growing.

Rotor blades

Three blades of fiberglass and carbon fiber composite, 50 to 80 meters long on current land-based wind turbines and longer offshore. Each rotor blade is an airfoil, shaped to generate lift efficiently across changing wind speed. Blade length keeps growing because energy capture scales with swept area: doubling blade length quadruples the area the rotor harvests. Blades also take the worst environmental abuse of any component: leading edge erosion, lightning strikes and constant flexing over hundreds of millions of load cycles.

Hub

The rotor hub connects the blades to the main shaft and carries the pitch bearings that let each blade rotate around its own axis. The hub assembly, with its aerodynamic spinner cover, is what you see turning; blades and hub together form the rotor.

Nacelle

The housing at the top of the tower that contains the drivetrain and most other machinery. The nacelle protects its contents from weather while its cooling openings, and the layout of everything inside, are engineered around one enemy: heat. Everything from the gearbox to parts of the electrical system lives here.

Main shaft and bearings

The low-speed main shaft carries the rotor’s enormous torque into the nacelle, supported by the main bearing. It is one of the most heavily loaded rotating parts of the turbine.

Gearbox

A multi-stage transmission system that converts low rotational speed and high torque into the fast rotation the generator needs. The gearbox is one of the most expensive parts of a wind turbine to replace, which is why oil analysis and vibration monitoring concentrate here. Direct-drive designs remove it at the price of a larger, heavier generator and greater dependence on the converter. Neither approach is simply better: geared platforms trade gearbox maintenance for a compact generator, direct-drive trades mechanical simplicity for more power electronics.

Yaw system

Electric yaw drive motors rotate the entire nacelle to face the wind as the wind direction shifts, guided by the wind vane on the roof. A yaw brake holds position between moves. Pitch and yaw together are how the turbine steers itself through changing weather.

Pitch system

Electric or hydraulic actuators in the hub rotate each blade to control power capture and to feather the blades out of the wind in storms. The pitch system is the turbine’s primary aerodynamic brake and one of its most safety-critical moving parts.

Anemometer and wind vane

Instruments on the nacelle roof measuring wind speed and direction. Their signals drive when the turbine starts, how it yaws, and when it shuts down for storm protection.

Mechanical brake

A disc brake on the high-speed shaft, used for service stops and as a backup to aerodynamic braking. During maintenance it locks the drivetrain safely.

The Electrical System: Where Wind Becomes Sellable Power

This is the part most guides compress into a sentence, and it deserves better, because the electrical system turns raw rotation into marketable electric power and determines the efficiency and reliability of everything upstream. These are its key components.

Generator

The generator converts mechanical rotation into electrical energy, typically at around 690 volts. Most installed turbines use a doubly fed induction generator, whose rotor current is controlled through the converter via slip rings, while newer and direct-drive platforms use permanent magnet synchronous machines with all output flowing through the converter. The doubly fed design is why so much of the existing fleet depends on converter health: the converter does not just condition the output, it actively controls the generator. Either way, the generator alone cannot deliver grid-quality power, because its output frequency wanders with the wind.

Frequency converter

The frequency converter is the turbine’s power electronics heart and the reason variable wind can feed a fixed-frequency grid. Inside the cabinet, a generator-side module of IGBT power semiconductors rectifies the variable output into a DC link stabilized by capacitor banks, and a grid-side module inverts it back into clean alternating current locked to grid frequency. A control unit runs the switching thousands of times per second, filters smooth the waveform, and a dedicated cooling system, air or liquid, removes the heat all of this produces. The converter also delivers the grid code services modern networks demand: reactive power, voltage support and fault ride-through. Partial-scale converters on doubly fed machines process roughly a third of rated power; full-scale converters process all of it.

Because it switches the turbine’s entire output while living with heat and vibration, the converter is also one of the hardest working parts of the turbine, with its own wear items: cooling fans and pumps, capacitor banks, IGBT modules, contactors and control boards.

Transformer

Steps the converter’s low-voltage output up to the medium voltage of the wind farm’s collection network, typically 10 to 35 kV. It sits in the nacelle or tower base depending on the platform.

Switchgear and main circuit breaker

The main circuit breaker and its switchgear connect and protect the turbine electrically, isolating it from the grid for service or during faults. Breakers and contactors wear with every switching operation, which makes them regular service items.

Control system and SCADA

The turbine controller supervises every subsystem, executes start and stop sequences, and reacts to the anemometer, the converter and dozens of sensors. SCADA links each turbine to the wind farm’s operations center, streaming data and alarms that make remote diagnosis possible.

Cables, slip rings and rotary connections

Power and signal cables run the tower’s height with a loop that tolerates nacelle rotation. Slip rings carry power and signals into the rotating hub for the pitch system, a small detail with an outsized failure record.

Lightning and protection systems

Receptors in the blades conduct lightning down through the structure to the foundation earth, and surge protection shields the sensitive electronics. Protection systems rarely get attention until the storm that proves their worth.

Auxiliary systems

Around the headline components sit the systems that keep them alive: cooling circuits for the gearbox, generator and converter, hydraulic power units, cabinet heaters and dehumidifiers for cold or humid sites, and the service lift and cranes that make maintenance physically possible. Auxiliaries cause few headlines and many service calls.

Onshore vs Offshore: Same Parts, Different Stakes

An offshore wind turbine contains the same part list as its land-based cousin, scaled up and hardened. Blades pass 100 meters, foundations become monopiles or floating structures, and every material faces salt corrosion. The economics change more than the anatomy: when a vessel and a weather window stand between a service team and a failed component, reliability engineering and remote diagnostics stop being nice to have. That is one reason offshore platforms lean heavily on full-scale converters and rich condition monitoring.

Which Parts of a Wind Turbine Fail Most Often?

Across published reliability studies of wind turbine components, the most frequent failures cluster in the pitch system, the electrical system including the frequency converter, and the control system, while gearbox and generator failures cause the longest downtime per event. That pattern should steer any spare parts strategy: the fast movers are electrical. In ConverterTec’s service data across 24,500+ converters, the typical wear items are cooling components, capacitor banks, IGBT modules, contactors and control boards, exactly the converter spare parts worth holding on the shelf. And because most of these components can be repaired rather than replaced, component-level converter repair usually restores a failed module for a fraction of the new part price.

The Converter Specialists

Wind turbine manufacturers (OEMs) such as Vestas, Siemens Gamesa and GE build the machines, but a large share of the installed fleet runs frequency converters that carry names no longer on the market. Converters delivered under the SEG and Woodward names are ConverterTec designs, those names were earlier identities of the same company, and the same applies to IDS. Units under the Efacec name were designed and engineered by ConverterTec and built under contract. ConverterTec provides converter aftermarket services for all of these platforms, with repair, spare parts, upgrades and retrofit, and supports third-party platforms such as GE with repairs and replacement parts of its own design, offered as a ConverterTec product for GE turbines. 237 customers worldwide, ISO 9001 certified, with a US office in Loveland, Colorado.

FAQ: Wind Turbine Parts

What are the 5 main parts of a wind turbine?

The five main parts of a wind turbine are the rotor (blades and hub), the nacelle with the drivetrain (main shaft, gearbox and generator), the electrical system (frequency converter, transformer and controls), the tower, and the foundation.

What are the 12 parts of a wind turbine?

A typical 12-part breakdown lists the foundation, tower, rotor blades, hub, nacelle, main shaft, gearbox, generator, frequency converter, transformer, yaw system and pitch system. Longer lists add the anemometer, wind vane, brake, controller and switchgear as separate items.

What is the nacelle of a wind turbine?

The nacelle is the housing at the top of the tower that contains the drivetrain and supporting machinery: main shaft, gearbox, generator, and depending on the platform the converter, transformer and control cabinets. It rotates on the yaw system to keep the rotor facing the wind.

What does the converter in a wind turbine do?

The frequency converter transforms the generator’s variable-frequency output into grid-quality power at a fixed frequency and voltage. It also provides grid support functions such as reactive power control and fault ride-through, and in doubly fed machines it controls the generator itself.

How does a wind turbine generate electricity?

Wind turns the rotor blades, the rotor turns a shaft, and a gearbox increases the rotational speed for the generator, which produces electric current. The frequency converter conditions this output to match the grid, and a transformer steps up the voltage for transmission.

What materials are wind turbines made of?

Mostly steel (roughly two thirds to four fifths of total mass, including the tubular steel tower), fiberglass and carbon composites in the blades, cast iron in hubs and frames, copper in the generator, cables and transformer, and silicon power semiconductors in the converter.

Knowing the parts of the turbine is step one; knowing which of them will ask for attention in year 12 is what protects the budget. For the converter, the part list above is the daily work of ConverterTec’s service teams.

More Media

18. November 2025
News

The people behind ConverterTec mission

ConverterTec is offering a closer look into the people who drive its mission forward with a newly released video showcasing daily life across its Aftermarket […]

Read more
5. March 2026
News

ConverterTec at WindEurope 2026 in Madrid

ConverterTec Aftermarket & Service will be attending the WindEurope Annual Event 2026 in Madrid from 21–23 April. Visit us at Booth 9-H60 to meet our […]

Read more
ConverterTec Wind Europe 2025
19. February 2025
News

ConverterTec participates as an exhibitor at the WindEurope 2025 in Denmark

ConverterTec will once again be represented at the WindEurope 2025 in Copenhagen, Denmark, with a joint stand, where it will present its activities and capacities […]

Read more
30. September 2026
News

Full Converter vs DFIG: Two Wind Turbine Topologies Compared

Nearly every utility-scale wind turbine on the planet belongs to one of two electrical families: the doubly fed induction generator (DFIG) with its partial-scale converter, […]

Read more
ConverterTec Cleanpower 2025 Phoenix
16. May 2025
News

ConverterTec Aftermarket & Service Presents Improved GE 1.x Phase Modules at ACP 2025

Convertertec will be exhibiting at the American Clean Power 2025 in Phoenix, Arizona, from May 19th to 22nd! At our Booth #4339, we will be showcasing […]

Read more
3. September 2026
News

How Much Does It Cost to Repair a Wind Turbine Converter?

There is no single figure, because a wind turbine repair can mean anything from a filter cartridge to a new gearbox. What can be answered […]

Read more